HEAD dynamic water jet series
Professional design for the angle cutting and 3D cutting, can be used in ceramic, marble pattern, and curves, conical surface,bevel.
The AC 5-axis system adds the A axis (around the X-axis rotation) and C axis(around the Z-axis) based on the standard three-axis (X-axis Y-axis Z-axis). AC 5-axis system is the most popular 5-axis system in the world market at present.
In order to meet the world market demand, Head company developed the same level 5-axis system compared with the world’s most advanced 5-axis system.It has good quality and high cost performance.
HEAD HD5X-AB five axis water jet system is the solution for high quality ceramic, marble pattern, anti tilt and metal vertical precision cutting. By changing the angle of cutting head in horizontal and vertical optimize tilt to achieve any angle control, the max tilt angle is 8 degree. Can adjust the angle in tiny, and cut any material.
1.The cutting head can be any angle cutting, eliminate the small surface and big bottom, which makes the gap is smaller, no need polishing, which reduces the cost.
2.To let the complex drawing more beautiful and easy to operate.
3.Turning without stop, no turning point, which makes the cutting speed faster, unsmooth cutting surface will not affect the matchin.
4.The tilt angle can be adjusted automatically, with good cutting result.
 ▲Wireless remote control handle(Option) With display function , can real-time display X,Y, Z axis workpiece coordinate,mechanical coordinate , speed , step value, etc . Can set workpiece zero point , back to zero point , back to mechanical zero point , feed speed adjusting ,step value ,high pressure , oil pump , water pump , abrasive controller , HP on/off valve , simulate processing , XYZ positive and negative direction moving ,etc. Adapt high performance wireless transmission technology , frequency hopping transmission , data encryption , strong anti-jamming ,stable and reliable , support 64 sets of wireless remote control using meanwhile .  ▲Water cutters for water softener(Option) Removes calcium, magnesium ions in thewater, prolongs the service life of high-pressure parts such as high-pressureseals and nozzles Out of water up to 2 tons / hour, which canuse for multiple devices.  ▲Cooling tour(option) To protect the hydraulic system continuous working Save water resources Can guarantee the hydraulic temperature under 45 Low cost compare with oil chiller Can meet the system working requirement  ▲Water cutting machine for oil cooler(Option) The host uses a new imported brand-name compressor, reliable operation, high efficiency, low noise and other imported brands dedicated pump, pressure, high stability, durable and durable. The use of imported digital controller, high precision, the use of a wide range, can effectively control the oil temperature in any range of requirements. Can work at ambient temperature at 45 degrees to maintain normal work.  ▲FastCAM(Option) Professional optimize nesting engine, with the automatic, manual, matrix, auto keep in ,and auto manual CD-I nesting function Support multi nesting way, include DXF/DWG/CAM/NC Single or series read or input file, can nest fast Set part auto nesting Rest board editor and control, and nest to irregular board Single part and multi part auto continuous nesting Manual nesting, part can move, rotate, turn  ▲Automatic height tracking system The auto height tracking system which isdeveloped and researched by Shenyang HEAD water jet has the function to set thedistance between cutting nozzle and cutting part. The distance is oftenrequirement by 3-5mm. To set the distance by traditional way will causeproblems often, hard to handle, which will cause the hit of them. The autoheight tracking system will solve the problem well. The auto height tracking system can becontrolled by professional water jet software, before cutting, the tracking pinwill begin to go down, guarantee the distance between cutting head and cuttingpart is 3-5mm, then the Z axis will go down, until the pin touch the surface ofcutting part. The limit sensor on the system will get thesignal, after it is sent to the CNC control system, it will lift upautomatically ( This function is achieved by air, the air pressure is 0.2Mpa),not affect the working of cutting head. Thesystem can be used on the standard 3-axis cutting head, dynamic cutting head,to guarantee the cutting accuracy , it is a very professional auto tool settingdevice.  ▲Following device(Option) To solve the problem of irregular surfacecutting, HEAD water jet company has developed the following device. This systemcan cut well on the irregular surface at time. It is often used on the smallangle sloping or easy grade. This device does not need the air to make it back,it will follow the cutting head all the time, not affect the cutting. Thisdevice is suggested to use on the 3 axis cutting head.  ▲Loading Series According to many years actual cutting experience .Shenyang Head Science & Technology Co.,specially design two types of loading system for brittle material cutting . Floor-type loading system for large piece of marble cutting The cutting table adapts latest loading design, the max overturn angle is 85，the distance between loading material and ground is only 100mm，max load-bearing is 1000KG ,hydraulic lifting and some other designs can meet the requirement of marble cutting .The situation many personnels are needed for loading material is changed , nowadays only 1 person is needed for the whole loading process .simple，convenient ，greatly reduce the labor cost and minium the marble breakage.This cutting table structure is 1st time adapted in domestic.It gains high praise once used by lots of marble processing clients. Another loading system is professional designed for large piece of glass handling after processing. This cutting table can realize the longest 4000mm glass cutting , max load-bearing is 1000KG, the max overturn angle is 85，and hydraulic lifting is adapted .Glass breakage rate is very high during handling process , when cut in ordinary cutting table ,especially cutting large ares multiple irregular holes,the most popular toughened glass is very obvious at the current market . Strongly required by the glass processing clients , the glass loading system is designed successfully , it has solved lots of problems for glass deep processing , and gains consistent high praise . ▲Submerged platform Separated structure between water tank and moving system. This way can ensure the water tank keep a long time using life under the worse environment. The water tank equipped water level lifting system in standard components. This system is manual controlled by water level adjusting valve. This level can be adjusted according to actual situation. The water tank will not require water and additional actions from the operator. This system can limits the water jet spraying prominently by increase the water level over the cutting material, which can keep the cutting head clean more easily. Submerging the cutting material is a very effective solution to reduce the noise when cutting, even minimize the noise to 75db.  ▲Head new type movable auto abrasive removal system model HD75L Head new type movable auto abrasive removal system model HD75L, is our self-developed equipment specially for waterjet cutting removing waste abrasive. It is the most reasonable and simple abrasive removal system in the existing of waterjet cutting abrasive removal field. It has many advantages compared with traditional removal system. The advantages of movable auto abrasive removal system: 1.Whole abrasive removal process does not effect the waterjet normal cutting. 2.This removal is easy to operate, can clean the abrasive completely with a high speed. 3. Big volume 75 L, commonly remove twice a day at most. 4. Thick steel plate and perfect hydraulic system. 5.Strong strength and high stability 6.Environmental protection and energy saving 7.Mobility and humanization |
|
| |||||||||||||||||||||
